Home Contact Us Information Request Manufacturer's Agents Saf-T-Bar Festoon Systems (updated) Crane Controls Pendant Controls (updated) Remtron Radio Remote Controls (updated) Limit Switches (new) Workstation Cranes (new) Overload Protection and Weighing Sytems Cable-Hose Reels Slip Rings Cable and Hose Carrier Systems Industrial Cooling and Heating Systems ITNAC Lifting Accessories Peiner Grabs Vaculex Vacuum Tube Lifts (updated) Machine & Chip Protection	Machine Protection Products
	Way Wipers for Long-Life Machine Tool Protection
				Way wipers ensure that your close-tolerance machine tool slideway gets all the protection it needs from hot chips, abrasives and cooling agents. The replaceable tough polyurethane wiper blade is specially designed to seal against wear-causing agents. It is long lasting and will withstand heat up to 200° F. A frame overhang is incorporated in some models for situations where the blade would exposed to hotter chips. The frame is constructed of solid aluminum which is lightweight and non-corrosive. KABELSCHLEPP way wipers protect slide and guideways from impurities and ensure trouble-free operation. Advantages Customised solutions Easy to install Highly wear-resistant polyurethane lip Heat resistant up to +100°C Flexible at low temperatures up to -40°C Resistant to oils, grease, alkalis, water Type BA These way wipers are mostly used in areas where space is restricted or where wipers are protected by telescopic covers, bellows or link apron covers and in areas where no chips are produced. Type BAS With this type the light metal frame has a built-in protection for the wiper lip. These wipers are used where chips (no hot chips) are produced. To protect the wiper lip from hot chips and to clean the guideway of coarse and solid dirt particles, the wipers must be fitted with an additional protective lip made of stainless spring steel or brass. The protective strip and light metal clamping piece are fitted to the machine using wiper fixing screws. For straight way wipers with suitable hole pattern (hole spacing = 80 mm) no clamping piece is required.
	Apron Way Covers Low-Cost, Long-Life Machine Slideway Protection
				Apron way cover systems help maximize your machine tool investment. The strong aluminum extrusion provides positive protection of machine ways from hot chips, abrasives, and other wear-causing agents. The aluminum elements are interlocked with tough, long lasting polyurethane hinge elements. These aprons can be used instead of telescopic way covers, requires a minimum amount of space, and is a low-cost solution to potential high-cost repair or replacement.
	Telescopic Covers for Slideways and Guideways
				Telescopic covers provide the following benefits: Protect the slideways and guideways against dust, chips, coolants and grinding emulsions Prevent the accumulation of chips on the machine bed Provides easy access across machine slides to tool and work piece areas Reduces accident risks Improves appearance of the machine Type MA 8 and MA 12 way wipers mainly operate on telescopic covers providing wiping as well as pulling action. In case of space restrictions wipers can be fitted vertically to the guideway by means of a carrier plate. The wipers are made of sheet steel profile with a vulcanised highly abrasion resistant wiper lip. Resistant to mineral oils and coolants. Standard length: 500 mm The supporting strip can also be designed wider. A high-grade steel protective strip is used to protect the wiper lip from hot swarf. In this case, the wiper can be used only in parallel to the guideway! Type designation of the protective strip: Type (MA 8) S for wiper MA 8 Type (MA 12) S for wiper MA 12 The wipers in type series MA 12.1 and MA 18 should be used only with telescopic covers. The wiper lip can be exchanged. Structure and material as described under MA 8 and 12. Standard length: 3000 mm Fabricated versions are possible individually according to your drawing.
	Conical Spring Covers Protects Machinery
				Conical spring covers provide an effective and inexpensive method of protecting sensitive areas on and around machinery. The completely enclosed design offers protection for: lead screws, ball screws, hydraulic rods, die post, and personnel. Benefits Completely enclosed design. Dynamic telescope action results in automatic expansion and contraction. No mounting clamps required. Mounting "seats" available. Available in Stainless or Carbon Steel. Good aesthetic appearance.
	For further information please contact us at info@ipandc.com